Resultado final Other (1) Project graphic identity and website Project graphic identity and website (M3, EWF). Publicaciones Conference proceedings (3) Numerical study of rolling process on the plastic strain distribution in wire + arc additive manufactured Ti-6Al-4V Autores: M. Abbaszadeh, J. Hönnige, F. Martina, N. Kashaev, S. W. Williams, B. Klusemann Publicado en: PROCEEDINGS OF THE 22ND INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING: ESAFORM 2019, 2019, Página(s) 150019 Editor: AIP Publishing DOI: 10.1063/1.5112695 Fundamental study on additive manufacturing of aluminum alloys by friction surfacing layer deposition Autores: Junjun Shen, Stefanie Hanke, Arne Roos, Jorge F. dos Santos, Benjamin Klusemann Publicado en: PROCEEDINGS OF THE 22ND INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING: ESAFORM 2019, 2019, Página(s) 150015 Editor: AIP Publishing DOI: 10.1063/1.5112691 Mapping of non-destructive techniques for inspection of wire and arc additive manufacturing Autores: Lopez, A., Bacelar, R., Pires, I., Santos, T., & Quintino, L Publicado en: In Proceedings of the 7th International Conference on Mechanics and Materials in Design (M2d2017) (Vol. 1844), 2017, Página(s) PAPER REF: 6654 Editor: INEGI/FEUP Peer reviewed articles (6) Numerical Investigation of the Effect of Rolling on the Localized Stress and Strain Induction for Wire + Arc Additive Manufactured Structures Autores: M. Abbaszadeh, J. R. Hönnige, F. Martina, L. Neto, N. Kashaev, P. Colegrove, S. Williams, B. Klusemann Publicado en: Journal of Materials Engineering and Performance, Edición 28/8, 2019, Página(s) 4931-4942, ISSN 1059-9495 Editor: ASM International DOI: 10.1007/s11665-019-04249-y Phased Array Ultrasonic Inspection of Metal Additive Manufacturing Parts Autores: Ana Beatriz Lopez, João Santos, José Pedro Sousa, Telmo G. Santos, Luísa Quintino Publicado en: Journal of Nondestructive Evaluation, Edición 38/3, 2019, ISSN 0195-9298 Editor: Kluwer Academic/Plenum Publishers DOI: 10.1007/s10921-019-0600-y Non-destructive testing for wire + arc additive manufacturing of aluminium parts Autores: João B. Bento, Ana Lopez, Inês Pires, Luísa Quintino, Telmo G. Santos Publicado en: Additive Manufacturing, Edición 29, 2019, Página(s) 100782, ISSN 2214-8604 Editor: Elsevier BV DOI: 10.1016/j.addma.2019.100782 Wire plus arc additive manufactured functional steel surfaces enhanced by rolling Autores: Philip Dirisu, Ganguly Supriyo, Filomeno Martina, Xiangfang Xu, Stewart Williams Publicado en: International Journal of Fatigue, Edición 130, 2020, Página(s) 105237, ISSN 0142-1123 Editor: Elsevier BV DOI: 10.1016/j.ijfatigue.2019.105237 Analysis of fracture toughness properties of wire + arc additive manufactured high strength low alloy structural steel components Autores: Philip Dirisu, Supriyo Ganguly, Ali Mehmanparast, Filomeno Martina, Stewart Williams Publicado en: Materials Science and Engineering: A, Edición 765, 2019, Página(s) 138285, ISSN 0921-5093 Editor: Elsevier BV DOI: 10.1016/j.msea.2019.138285 Formability of a wire arc deposited aluminium alloy Autores: C. M. A. Silva, I. M. F. Bragança, A. Cabrita, L. Quintino, P. A. F. Martins Publicado en: Journal of the Brazilian Society of Mechanical Sciences and Engineering, Edición 39/10, 2017, Página(s) 4059-4068, ISSN 1678-5878 Editor: Brazilian Society of Mechanical Sciences and Engineering DOI: 10.1007/s40430-017-0864-z Book chapters (1) Mechanical Properties Enhancement of Additive Manufactured Ti-6Al-4V by Machine Hammer Peening Autores: Leonor Neto, Stewart Williams, Jialuo Ding, Jan Hönnige, Filomeno Martina Publicado en: Advanced Surface Enhancement - Proceedings of the 1st International Conference on Advanced Surface Enhancement (INCASE 2019)—Research Towards Industrialisation, 2020, Página(s) 121-132, ISBN 978-981-15-0053-4 Editor: Springer Singapore DOI: 10.1007/978-981-15-0054-1_13 Non-peer reviewed articles (1) Non-destructive testing application of radiography and ultrasound for wire and arc additive manufacturing Autores: Ana Lopez, Ricardo Bacelar, Inês Pires, Telmo G. Santos, José Pedro Sousa, Luísa Quintino Publicado en: Additive Manufacturing, Edición 21, 2018, Página(s) 298-306, ISSN 2214-8604 Editor: Elsevier BV DOI: 10.1016/j.addma.2018.03.020 Buscando datos de OpenAIRE... Se ha producido un error en la búsqueda de datos de OpenAIRE No hay resultados disponibles
